Bathtub will not Drain at All

Best Selling Bathtub

Something is calming about taking a bath. Taking an unintentional bath every time you want to take a shower has the opposite effect. It is important to keep standing water off of your property. Keep calm and carry on. If you have standing water in your bathtub drain, here are a few things you can do before calling the plumber.

Here is a list of the tools and supplies you will need

  • Bucket
  • Rag
  • Screwdriver
  • Plumber’s Snake
  • Plunger
  • Rubber Gloves
  • Baking Soda
  • Distilled White Vinegar
  • Salt

The most common causes of a clogged bathtub

The soothing effects of bathing are unmatched. However, you might find that relaxation quickly turns to frustration if your bathtub drains slowly after you pull the plug – or, worse yet, if it doesn’t drain at all!

Some of the most common reasons that cause your bathtub not to drain are listed below. The question appears to be, what can be done to fix a slow drain? We’ll address these questions below.

  1. Clogged Hair

Showers and tubs with drainage problems are probably caused by this problem most commonly. Think of it this way: you’re in the tub, cleaning yourself from head to toe. Sooner or later, some of your hair is going to fall out because of all that scrubbing! Fortunately, most of it ends up getting flushed down the drain.

You may notice that your drain initially drains more slowly if you have a hair clog. Then, slowly, the drain will get slower and slower until it becomes evident that something is blocking it.

  1. Dirt and Grease Buildup

The likelihood of this one happening is not as high, but it still has the potential to happen. After all, taking a bath is a good way to get rid of all that dirt and grime accumulated during the day. If you’ve been working hard and have to wash off a lot of dirt from your body, some of it may get stuck in the drain line.

  1. Soap Scum

The build-up of soap in your drain can obstruct water flow and cause your drain to slow down. Gradually (and with a clogged hair follicle, it gets even worse), this will happen.

  1. Bigger Objects

Our focus so far has been on small items that slowly accumulate and clog up your bathtub drain. There’s also always the possibility that a larger object has somehow managed to wedge itself in your drain line. You’d better believe it happens to you if you have kids! THESE ITEMS CAN BECOME SIGNIFICANT OBSTRUCTIONS from LEGO pieces to jewellery (yes, the proverbial wedding ring can end up down your drain).

  1. Septic Backup

Oh no! This is not something we should dwell on for too long. However, if your tub isn’t draining as it should – or if water is backing up into your tub – then you may discover that a septic system backup is a culprit.


The dangers posed by standing water

Even if you have standing water in your bathtub for just a few hours, it can still pose a danger to your health and your home. A standing body of water is a breeding ground for flies, dragonflies, and mosquitoes. If you don’t stop them from growing and reproducing, they’ll become a nuisance.

In addition to carrying diseases that can harm humans and animals, flies can carry various diseases. In addition, flies can transmit tapeworms and heartworms. Standing water may also cause mildew and mould to form on the shower walls.

How to Unclog a Standing Bathtub Drain


1. Clear All Visible Blockages

It’s essential to take all the necessary measures first to avoid adding more water to the tub. First, make sure all the standing water is removed with a bucket. Then, use your fingers to remove any debris you see. First, put on some gloves. If there is any icky gunk, you should avoid touching it directly.

If you do this, you can probably get everything cleared out quickly. In addition, hair, soap scum, and bathing accessories can easily find their way into the drain and clog it up. A massive hairball causes many clogs.

2. Fill the tub with boiling water and flush the drain

Trying this easy trick could be helpful if you removed the gunk, but it did not work. Put boiling water in the drain to get rid of the gunk. There is no guarantee that this step will unclog grease or physical blockages. If there is an obstruction causing the clog, it’s worth trying if it is small or suitable.

When you connect the tub to metal pipes, you can safely use it. PVC pipes, on the other hand, should not be used for this. You might soften the joints in these pipes. Try hot water rather than boiling water if you are unsure of the kind of pipes you have.

3. To unclog a bathroom drain, plunge your bathtub.

Before you begin, make sure that there is no standing water. You will need a screwdriver to remove the overflow cover. Check first if there are any obstructions.

Once you have removed it, you should jam a piece of cloth into the hole. To ensure that no air escapes during plunging, make sure the rag is firmly inserted. The plunging will push out the rag, so you’ll need to use your free hand to ensure it stays lodged.

The best thing to do would be to find a helper who can hold the cloth and make the whole process much more manageable. Plunging requires you to set aside a considerable amount of time. The first time you use it, you might think it isn’t working since it takes some time. It may take some time and effort to solve the problem, but you may succeed if you invest some energy.

Once the water starts draining, you’ll know the machine is working. As soon as your pipe looks clear and the method proves successful, it would be best if you cleared any remaining residue with hot water. If it does not work, snaking the drain is your next best option.

4. Use a Plumbing Snake

If you are unfamiliar with plumbing snakes, this may be a challenge, but don’t let it stop you. To use the power snake, you will need a cable that is 14 inches long. There is no need to spend a lot of money on it. Instead, you can rent it from a tool rental store.

To remove the overflow plate, first, remove the overflow pipe. Then, instead of inserting the snake in the bottom drain, you should insert it in the overflow opening. The snake should be run with one hand while the cable should be held firmly with the other. Do not rush the process. Instead, slowly and steadily feed the cable into the drain.

You shouldn’t attempt to snake the drain even if it seems more manageable. If you do, the pipe might be broken. However, if you can reach the drain opening, do so. There shouldn’t be more than a foot between the cable and the opening. Please make sure the cable doesn’t kink upon you by keeping it tight.

When the cable starts to bend, and you feel it is about to kink, pull it back. If that happens, you need to slow down even more. You could be experiencing tension if there is a heavy blockage. Try pulling the cable out now and then to see if you already have the clog on the snake.

The snake may have a slight bend or hook that may allow the cable to pass the trap. You might want to bend the cable if things become complicated.

This distance is usually less than 10 feet between the toilet mainline and tub drain. In other words, if the clog was not removed after running more than 10 feet of cable, it may have crept up the vent line after hitting the trap.

In most cases, you will hear the cable going up the wall if it is going the wrong way, but there will be no sound if it is going in the opposite direction. This problem can be resolved by running the cable backwards instead of forwards. There are no guarantees that this will work, but you don’t have another DIY option to unclog the left-over clog.

5. Baking soda, white vinegar, and boiling water

Again, do not use boiling water if you are using PVC pipes. Initially, the water should be sprayed with baking soda to loosen any residue. Be sure it gets into the water. To make things easier, use a funnel or measuring cup.

Once this is done, pour half a cup of distilled white vinegar down the drain. Once you have done that, you should hear and see some fizzing. Once the fizzing starts, cover the drain and wait for it to stop.

It should be no surprise that the reaction looks a bit dramatic since vinegar and baking soda make an unusually potent combination. Wait half an hour after the fizzing has stopped. At this point, you can boil the water.

It should be flushed down the drain. If it is not draining, repeat the procedure. You can also run hot water from the faucet. The non-chemical solution below may also work if the above one does not.

6. Baking soda, salt, and boiling water can be used.

Baking soda and salt may suffice if vinegar is not available in your house. First, pour one cup of baking soda down the drain. Afterwards, mix half a cup of salt with baking soda before pouring it down the drain.

At least two hours are necessary to allow it to sit. If possible, leave it overnight. If the drain still has standing water, flush it out the next morning. Turn on the hot water faucet if it seems to be cooperating.

7. Use Chemicals Down the Drain

You’ll need to turn to the big guns if you can’t fix the problem with staple household items. Chemicals can be harmful, so this should be the last resort when it comes to DIY solutions. An effective clog buster can be found at any hardware store. Nevertheless, you need to make sure the product you want to buy is suitable for your bathtub pipe. You should use a cleaner that’s made specifically for bathtubs.

If you have a bathtub, Drano or Crystal Lye Drain Opener may be the best option. Make sure to use gloves when handling these cleaners. Avoid splashing the cleaner.

Please check the label for instructions. The drain may remain blocked for up to an hour after you pour the chemical down it. It’s not necessary to flush the cleaner with hot water as you would w

ith other methods.

Why Do Clogged Bathtubs Happen So Frequently?

There appears to be a greater problem with clogged bathtubs in some parts of the country than in others. Therefore, you are probably not to blame. The situation is circumstantial.

Water conservation is a concern for many residents. Additionally, many people use bath products containing oil. Therefore, clogs are inevitable when there’s not enough water, plenty of oil-based products, and a bit of hair in the drain.

Some areas have tap water with higher mineral content. Although it isn’t dangerous to your health, your pipes do not like it. The “water” becomes hard because of it, and hard water is partially to blame for clogged drains. Additionally, it can cause dirty water to appear brown.

Preventing a Clogged Tub Drain

Whenever possible, avoid bathing with oil-based products. If you have to use these products, always make sure there is enough hot water available. Make sure the drain is covered, or a filter is used. Clean the opening whenever you see that debris is starting to accumulate. If your pipes become clogged, use vinegar, baking soda, and boiling water to clean them.

When to Call a Plumber To Unclog A Tub Drain With Standing Water

It’s good for you to be enthusiastic about DIY projects. Maintaining a healthy home and saving money can be achieved with this. Nevertheless, if none of these solutions works, a plumber should be called in. If you find yourself panting while you are frustratingly jamming the snake cable down the overflow opening, you should call a plumber and get some peace of mind. Your bathtub drain should be unclogged in under a day by a professional plumber.


There is nothing more unpleasant than a blocked bathtub drain. When left undisturbed, the water in the bathtub basin won’t drain, accumulating bacteria and transforming into a cesspool. To stop this from happening, make sure you deal with your bathtub drain clog immediately.

Smart Straw
Enable registration in settings - general